Shell Sand Moulding :

USE : It is use to collect the representative sand sample.
Specifications : It consist of long pipe having one end Hard Tip with handle

USE : It is use to collect the representative sand sample with proper mixing.
Specifications : It consist of long pipe having one end Hard Tip with handle

USE : It is use to drying the sand sample.
Specifications : Infra Red Lamp, 275 Watts, Drying Chamber Drying Pan.

USE : It is use to determine moisture % in Raw sand and Green sand.
Specifications : Capacity 10 % Moisture With Single Pan Balance, Absorbent Compound And Carrying Case

USE : It is use to determine Tensile Strength of shell sand in hot condition.
Specification :

01) Teflon coated Two Hot Plates, Controlled By Digital Temperature Indicator And Controller (0-300 o c).
02) Loading and unloading mechanisms operated by manually and auto by electronic control.
03) Digital Pressure Indicator to read tensile strength up to 55 kg/cm 2 .
04) Load Cell.
05) Hard crome plated tensile Jaw set.
06) Waste sand collection tray.
07) Jaw Lifting tongue.
08) Sand Filler Cum Scrapper
09) Cleaning Brush.
10) Working on 230 volt, 50 cycle, 1.6 Kw AC Power Supply

Use : To Prepare the standard specimen
Specification : Contains standard specimen Jaw

USE : It is use to determine melting point of Resin Coated Sand.
Specification : With Heating Unit, Sand Distributor Digital Temperature Indicator And Controller, Brush.

USE : It is use to determine Pill Off and Build Up property of shell sand.
Specification : Heater -1000 Watts, 230v.A.C. Supply. With Thermostat, Heating Plate, Funnel, Two Trays

USE : It is use to determine pill of f and build up property of shell sand.
Specification : Heater -1000 Watts, 230V A.C. Supply. With Digital Temp. Indicator Cum Controller, Heating Plate, Funnel, Two Trays

USE : It is use to determine gas evolution in the shell sand.
Specification : Heater-1200 Watts, 230v.,A.C.Supply.With Furnace Of 1200 o c Cap., Digital Temp. Indicator-Controller, Combustion Tube, Boats, Pusher Measuring Tube.

USE : It is use to determine surface hardness of Core Mould.
Specification : Harden Tip, to Measure Hardness of Cores 0 To 100 No.

USE : It is use to prepare shell sand in hot condition to check the resin properties under standard condition.
Specification : Mixture – Cap. - 5Kg [Batch], Motor with Gear Box1/2 HP Single Phase, Scraper - 2 Nos., window to see the inside process Heating unit – 6 kw, Blower – ¼ hp single phase, 230 AC volts.

Use: it is used to prepare the standard specimen for transverse strength of resin coated sand.
Specifications : Split Core Box To Prepare Transverse Specimens of 1/4X 1” X4” size with help of Hot Tensile Tester

Use: It is use to determine Transverse Strength of resin coated sand.
Specifications : Suitable For Transverse Strength. Capacity 100 Kg/Cm 2 . Motorized Loading unloading Mechanism, Load Cell, Digital Transverse Strength Indicator. Suitable for specimen size 1/4X 1” X4”

Use:It is use to determine to measure the distortions behavior of chemically bonded sand when exposed to heat.

Use: It is use to determine Transverse Strength of resin coated sand.
Specifications : Suitable For Transverse Strength. Capacity 100 Kg/Cm 2 . Motorized Loading unloading Mechanism, Load Cell, Digital Transverse Strength Indicator. Suitable for specimen size 1/4X 1” X4”

USE: It is use to standardize the pressure indicator and temperature indicator of Hot Tensile Tester.
Specifications :
1) It Consist plate with wire rope and hanger & temp indictor cum controller Calibrator at two different point
2) It require set of weights 20kg, 10kg & 5kg - 2 Nos.

Use: it is used to standardize the mould & core hardness tester
Specifications : consist of instrument Clamping spring & 5nos standard weights.